[if !mso]> [if !mso]> [if gte mso 9]>

答复: [EDK DEV] questions about PI-SCT

Subject: 答复: [EDK DEV] questions about PI-SCT

From: <TigerLiu@viatech.com.cn>

To: <dev@edk.tianocore.org>

Date: 2008-06-20 02:43:21

Maybe, I have to explain my question again !

I know : PEI-SCT not running through UEFI SCT UI.

 

Here are the steps I followed when doing this PEI-SCT test.

///////

I followed instructions described by PI_1_0_SCT_GetStarted ,added two test peims into my platform.dsc,and rebuilt  my edk project.

(in its chapter 5, it said : test-peims has to be added into the boot firmware volume,so tried to add two test-peims )

////// listed as below

Platform\IntelTest\TestCase\PI\PEI\PEIServices\PpiServices\PpiServiceFunction\PpiServiceFunctionPeim1\PeiSctPpiServiceFunctionPeim1.inf

Platform\IntelTest\TestCase\PI\PEI\PEIServices\PpiServices\PpiServiceFunction\PpiServiceFunctionPeim2\PeiSctPpiServiceFunctionPeim2.inf

 

////////

Then, I followed instructions decribed in chapter 2 in PI_1_0_SCT_Utility_User_Guide.

(1)     I created a Startup.nsh in fs2

(2)     Copied ManageMode.efi into fs2:\

(3)     Then reboot system, I found these two peims were dispatched successfully.

(4)     Boot into shell, I found a SCT.report in fs2:\ , but no test results were put into it.

 

Note : when run ManageMode.efi in shell, it tips init fail.

 

 


: Lin, Jie [mailto:jie.lin@intel.com]
: 2008619 18:21
: dev@edk.tianocore.org
: RE: [EDK DEV] questions about PI-SCT

 

Hi Tiger,

         There is another document PI_1_0 SCT Utility User Guide that contains detailed steps and example config files for running PEI SCT.

The PEI SCT is started by a command line shell application and not the UEFI SCT UI.

 

Cheers!

 


From: TigerLiu@viatech.com.cn [mailto:TigerLiu@viatech.com.cn]
Sent: 2008
619 18:15
To: dev@edk.tianocore.org
Subject:
: [EDK DEV] questions about PI-SCT

 

Hi,Jie:

My edk project is a real-platform efi Cbios, it runs on a real motherboard.

I had studied PI_1_0_SCT_GetStarted.

I followed its instructions to add these two peims into my platform.dsc.

 

Thanks

 

 


: Lin, Jie [mailto:jie.lin@intel.com]
: 2008619 17:57
: dev@edk.tianocore.org
: RE: [EDK DEV] questions about PI-SCT

 

Hi Tiger,

         Because PEI SCT has to change flash to insert PEI test cases, there is no such a workflow on a virtual platform NT32. Normally we run it on real platforms.

There is user guide documentation on http://sourceforge.net/projects/pi-sct/

Follow the instructions in it to create Startup.nsh file, Config.ini file. Note that the Config.ini file should be in Unicode format.

Run the ManageModule, after reboot, the report file will locate at the same directory with ManageModule.efi file

 

Cheers!

 


From: TigerLiu@viatech.com.cn [mailto:TigerLiu@viatech.com.cn]
Sent: 2008
619 17:28
To: dev@edk.tianocore.org
Subject:
: [EDK DEV] questions about PI-SCT

 

Hi:

I tried to run PEI-SCT on my edk project today.

I added two test peims into my platform.dsc,and rebuilt  my edk project.

////// listed as below

Platform\IntelTest\TestCase\PI\PEI\PEIServices\PpiServices\PpiServiceFunction\PpiServiceFunctionPeim1\PeiSctPpiServiceFunctionPeim1.inf

Platform\IntelTest\TestCase\PI\PEI\PEIServices\PpiServices\PpiServiceFunction\PpiServiceFunctionPeim2\PeiSctPpiServiceFunctionPeim2.inf

 

After reset system, I found these two peims were dispatched successfully.

But I could not find any log file on my harddisk.

(there are 3 fat partitions on my harddisk)

 

Where does this log file locate?

 

Thanks


: Lin, Jie [mailto:jie.lin@intel.com]
: 2008619 16:50
: dev@edk.tianocore.org
: RE: [EDK DEV] questions about PI-SCT

 

You can post it at the forum or submit a tracker at

http://sourceforge.net/projects/pi-sct/

 

Cheers!

Auber

 


From: TigerLiu@viatech.com.cn [mailto:TigerLiu@viatech.com.cn]
Sent: 2008
619 16:41
To: dev@edk.tianocore.org
Subject: [EDK DEV] questions about PI-SCT

 

Hello:

I have some questions about PI-SCT.

Could I post them here?

 

If not, please give me a mail-list address about PI-SCT.

 

Thanks